ASTM D5856 PDF

Test Method for Determination of Hydraulic Conductivity of Porous Material Using a Rigid-wall Compaction-Mold Permeameter. Start. Standard ASTM standard · ASTM D Status: Withdrawn · Replaced by: ASTM D Soil and Rock (I): D – D (ASTM VOL ). ASTM D Standard Test Method for Measurement of Hydraulic Conductivity of Porous Material Using a Rigid-Wall, Compaction-Mold.

Author: Mezikora Mujar
Country: Vietnam
Language: English (Spanish)
Genre: Art
Published (Last): 9 April 2007
Pages: 171
PDF File Size: 6.9 Mb
ePub File Size: 4.96 Mb
ISBN: 773-6-80548-400-9
Downloads: 86427
Price: Free* [*Free Regsitration Required]
Uploader: Vojora

The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used.

Continue shopping Proceed to checkout. Kontakt venligst Dansk Standard. Therefore, the results should be applied to field situations with caution and by qualified personnel.

Activation of monitoring failed – please try d585 later or contact us. However, this test method does not ensure complete saturation of the test specimen with water. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. It was not possible to unsubscribe – please try again later or contact the Danish Standard Please make sure you are logged in.

By tradition in U. Username or password invalid. By tradition in U. You must be logged in aastm sign up for monitoring You must be logged in to sign up for subscription.

  D-LINK DSL-G604T MANUAL PDF

ASTM D5856 – 15

Users of this standard are cautioned that compliance with Practice D does not in itself ensure reliable results. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applic. Please choose number of devices you want to open the document on.

The hydraulic conductivity of compacted materials that have hydraulic conductivities greater than 1?

ASTM D Standard

Experience has sometimes shown that flow patterns in small, laboratory-prepared test d58566 do not necessarily follow the same patterns on large field scales and that hydraulic conductivities measured on small test specimens are not necessarily the dd5856 as larger-scale values.

Activation of your subscription failed – please aastm again later or contact us. The printed version is available at half price when you buy the electronic version. Permeation with other liquids, such as chemical wastes, can be accomplished using procedures similar to those described in this test method. The problem tends to be of minimal significance for materials that swell when exposed to water for example, compacted, clayey soils but can astn a very serious problem for materials that might tend to shrink and pull away from the walls of the permeameter.

In cases where it is essential to saturate the test specimen fully with water, the compacted specimen may be tested using Test Method D However, when the hydraulic gradient acting on a test specimen is changed, the state of stress will also change, and, if the specimen or pore fluid is compressible, the volume of the test specimen or pore fluid will change.

  GANTTPROJECT MANUAL ESPAOL PDF

Test Method D is recommended for any material that tends to shrink when exposed to the permeant liquid. Do not show this again.

Link to Active This link will always route to the current Active version of the standard. Reliable results depend on many d58566 Practice D provides a means of evaluating some of those factors.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This test method applies to porous materials containing little or no air. There is a problem adding monitoring – please try again later There is a problem adding the subscription – please try again later.

Are you sure you want to unsubscribe monitoring? However, this test method is only intended to be used when water is the permeant liquid. It is not possible to buy in the shop – please contact us. Historical Version s – view previous versions of standard.

ASTM D5856

Are you sure you want to unsubscribe? Du abonnerer allerede dette emne.

The test method is designed to minimize the amount of air in the test specimen.