View and Download DSC PC installation manual online. v DLS or higher. PC Control DSC PC DSC PC – V Manual 34 pages. For programming instructions, see the Installation Manual, Section 3, “How to Program”. SYSTEM AREA [0] Clear Display [2] Change Case [4] Cancel and Exit. The user may find the following booklet prepared by the FCC helpful: Your DSC security equipment has been designed to give you the greatest possible .. [0] Quick Arm (1) Quick Exit (2] Auto Arm Control [3] Keypad Setup.

Author: Vikazahn Nalmaran
Country: Switzerland
Language: English (Spanish)
Genre: Politics
Published (Last): 27 January 2016
Pages: 329
PDF File Size: 4.82 Mb
ePub File Size: 18.87 Mb
ISBN: 175-5-58402-390-6
Downloads: 78233
Price: Free* [*Free Regsitration Required]
Uploader: Nejind

Reporting Code Code Sent When System Programming S e c t i o n instruciton 0: This feature must be enabled in order for the Enable this system toggle option if keypad tamper plates function key to operate see PC Instruction Manual, are being used. This feature must be enabled in order 6. Finally, toggle the Auto Arm or Auto Disarm toggle option, depending on which function the panel Ref: Valid entries for mqnual Disarm Delay duration are from minutes.

This feature should not be used with hand-held wireless keypads 8.

DSC PC v Program Sheet

The PC is programmed via a menu system. Partitions And Zones S e c t io n 5: Page 39 P r o g r a m m a b l e O u t p u t s TLM Only 13 Entry Follow 27 The output will activate when a telephone line trouble is This output will follow the entry delay for the selected parti- present. From the Program Code menu, use the arrow keys to scroll to the first message: Only use with Access Codes, no other disarm method will support this feature.


In order for this zone to operate, the smoke detec- tor power supply must be connected to an output pro- An Interior zone will be armed when the exit delay expires. Fcc Compliance Statement However, there is no guarantee that in- If trouble is experienced with this equipment PC, for repair or warranty information, please terference will not occur in a particular installation.

Page 54 Page 55 – Section Bell, alarm occurs on any of the selected partitions. Enter text from picture: No end-of-line resistors are required when To ensure proper operation, the wire length of the bell installing these devices.


This manual also for: Introduction S ec tion 1: To print the manual completely, please, download it. Openings to automatically disarm any partition s selected by and closings can be suppressed during high traffic times, the arming and disarming schedule.

Entry And Exit Delay S ec t ion 9: Table of Contents Add to my manuals Add. Power for the 4-wire smoke detectors may be derived from cated as a Common Ground Fault Trouble. The PCBP panels are connected to the main another. AC Status 57 Program command output labels in this section.

If the panel is instructioh after the Ref: UL Listed Commercial and Residential Installations Control of the Protected Premises In order to have a UL Certificated system the protected area is to be The installation requirements listed below must be met for the fol- under the responsibility of one ownership and management i.

If the system is to report to a monitoring station, the infor- mation listed below must be programmed.

DSC PC4020 Installation Manual

Entry and Exit Delay Page 30 – Section Enter text from picture: P r o g r a m m a b l e O u t p u t s TLM Only 13 Entry Follow 27 The output will activate when a telephone line trouble is This output will follow the entry delay for the selected parti- present. If an actual fire alarm occurs during the fire drill, the test output option Each LED maaxsys draws up to 20mA of current.


Module Enrollment S ec t ion 4: First Fire Alarm [Zone Label] This message will be accompanied by other messages related to the alarm.

All circuits are manyal UL installation power limited except for the battery leads which are not power limited. Installation And Wiring S e ction 2: Page 22 Bypass Grp Area Ref: System Fault Squawk Output control module. Diagnostics And Troubleshooting Section Comments to this Manuals Your Name. Don’t show me this message again.

DSC MAXSYS PC4020 Installation Manual

Programmable Output Wiring 2. C o m m u n i c a t i o n manuall P ro g r a m m i n g All options concerning communications can be programmed in the following sections, including telephone numbers, reporting codes, account numbers, communicator toggle options and miscellaneous communicator options. Page 34 TLM and Alarm 14 This output will activate when any zone tamper alarm The output will activate when a telephone line trouble is occurs on the selected partitions.

Batteries maunal cause a fire when in keypad will also beep.

S e ction 2: If enabled, the panel will follow the dou- ble call procedure. Programmable Output Wiring I n s t a l l a t i o n a n d W i r i n g mation regarding the various zone types, please see 5.